How to Set up a Tub: Set Up an Acrylic Bathtub and Bathtub Surround
How to Set up a Tub: Set Up an Acrylic Bathtub and Bathtub Surround
Blog Article
This post following next about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is without a doubt entertaining. Check it out yourself and decide what you think of it.
Setting up a bathtub isn't exactly rocket science, but it does require strong plumbing, woodworking, and also often, tiling abilities. Changing an old tub with a new one is also a moderately difficult project. If the old bathtub is easily easily accessible, the project can move speedily; if you need to open up a wall surface to eliminate the old tub and also place the brand-new bathtub, the job is much harder. In either case, the task is within a residence handyman's skills, although you will need an assistant to leave the old tub and embeded in the brand-new one. Make certain you have certified yourself for the task as well as fit trying it. Instead of hiring a contractor to take control of a halfway-completed job, it is better to take into consideration using one before you start. Possibilities are you might need a specialist plumber to make tube connections.
This write-up will help you set up a new bath tub in your bathroom if you have currently gotten a new tub as well as don't require to change the setup of your previous water system pipes.
Your devices as well as material list ought to consist of the following:
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you ought to do is separate the supply of water. After doing so, activate the taps to drain pipes any water staying in the system. The process of getting rid of the existing faucets can be rather bothersome due to the limited accessibility that is typically the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the faucets. Have a cloth prepared for the remaining water that will originate from the pipes. When the supply pipelines have been gotten rid of, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from turning during this procedure. Once the taps have actually been removed, the holes in the bath/basin will need to be cleaned of any type of old securing substance.
Before carrying on to fit the brand-new faucets, compare the pipe connections on the old faucets to the new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will require a plastic adapter to prevent damages to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end gives a link to the existent supply pipes.
If you need to fit a monobloc, then you will require lowering couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, position the tap in the installing hole in the bath/basin making certain that the washing machines remain in area in between the faucet and also the sink. Safeguard the tap in place with the producer offered backnut. When the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with regular faucet adapters. The previous kind needs to be connected to the tap ends first, tightening only by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Mounting the Bath tub
Making use of both wood boards under its feet, position the bath tub in the called for placement. The wood boards are valuable in equally spreading the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 little points.
The next goal is to guarantee that the bathtub is leveled all round. This can be achieved by checking the level and also changing the feet on the tub up until the spirit level reads level.
To set up taps, fit the bottom of the furthest flexible faucet adapter to the ideal supply pipe by making a compression join; then do the very same for the other tap.
Turn on the water system and check all joints and also brand-new pipework for leakages as well as tighten them if required. Fill the bathtub as well as likewise inspect the overflow outlet and the regular outlet for leakages.
Ultimately, repair the bath paneling as defined in the maker's instruction manual. Tiling and securing around the tub should wait till the tub has been made use of at the very least once as this will resolve it right into its final placement.
Planning for the Setup
Firstly, the sustaining framework supplied with the bathroom ought to be fitted (if required) according to the supplier's guidelines. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is necessary to make certain that if the faucet features a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps device to stop stress on the bathtub.
Fit the flexible tap adapters to the bottom of the two faucets making use of 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you utilize all of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath need to currently be ready to be suited its last position.
Tiling Around the Bath tub
In the area where the bath meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to split an inflexible seal, creating the water to penetrate the wall between the bath and also the tiling, leading to issues with wetness and also possible leaks to the ceiling listed below.
You can select from a selection of coloured sealers to blend in your fixtures and also installations. They are offered in tubes and cartridges, and can securing voids up to a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with spins of drenched paper or soft rope. Bear in mind to always fill up the tub with water before sealing, to allow for the movement experienced when the tub is in use. The sealer can fracture rather very early if you do not think about this motion prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also easily available on the market. It is recommended to fit the tiles using water-resistant or waterproof adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a person who reads about A Step-by-Step Guide to Installing a Bathtub, I think sharing that piece of content was a great idea. Feel free to take the opportunity to promote this blog if you appreciated it. Thanks so much for taking the time to read it.
Get A Free Estimate
Report this page